Model Number : NI-DP-201
Compliance Standard : Astm D2265
Description :- Dropping Point : It is the temperature at which the grease passes from a semi—solid to a liquid state under Controlled conditions of test. It is a numerical value assigned to a grease composition representing a corrected temperature at which the first drop of material falls from the test-cup and reaches the bottom of the test-tube. A grease sample in a grease test-cup is supported in a test-tube placed in an aluminium block oven at a preset Constant temp. A Sample thermometer is placed inside the tube and so positioned that it measures the temp. in the sample cup without coming in contact with the grease.
Technical Specifications :
|
Testing Capacity |
6 Grease samples at a time |
|
Temp. Range |
+5°C Ambient upto 400°C |
|
Temp. Control point |
121°C, 232°C, 288°C, 316°C |
|
Grease Cup |
Brass Cup – Internal Diameter = 10.7mm, Wall Taper angle = 4°, Wall Thickness = 0.4 +/- 0.13mm, Orifice diameter = 2.8mm, Outside diameter = 4.8 mm, Total Height = 12mm, Diameter = 10.7 mm |
|
Test-tube |
Thin walled with rim glass test-tube for sustaining 400°C,100 +/- 2 mm Height, ID = 11 +/- 0.2mm, OD = 13.7-14mm |
|
Exterior Body |
M.S Duly Powder Coated with Enamel Twin Color Combination |
|
Sliding Rod |
Made from Stainless Steel, 150 +/- 10mm,1.2 -1.6mm thickness – Can easily protrude through the Test-cup |
|
Heater |
Integral Cartridge type heater for efficient heating of Aluminium block. |
|
Operating Power |
700 Watt |
|
Insulation |
High-Temperature Cerawool insulation inside the chamber |
|
Temp. Control |
Microprocessor based PID Temp. Controller with Aotu-tune feature. |
|
Control Accuracy |
+/-1°C |
|
Temp. Detection |
3 Wire Pt-100 Sensor immersed inside the block for accurate detection of block temp. |
|
Heater Control |
Solid State relay for controlling the heater and maintain the required temp. in PID Controller |
|
Safety Feature |
Auto-over Temp. Cut off system. |
|
Thermometer |
0-400°C mercury filled glass thermometer |
|
Illumination |
White light lamp assembly provided at the backside for rear observation of drop point. |
|
Inspection Port |
High-temp. efficient Tuffen Glass for clear observation. |
|
Rubber Stoppers |
Placed on the test-tube and centrally bored for accurate positioning of thermometer inside the test-tube. |
|
Spatula |
Stainless Steel Spatula for filling and surfacing the grease inside test-cup |
|
Forceps |
For handing the test-tube after completion of test. |
|
Test-tube stand |
For placing the Test-tube inside the stand after completion of test. |
|
Instrument Dimensions |
L = 15” (38cm) x W = 17”(44cm) x H = 21” (54cm) |
|
Instrument Weight |
15-20 Kgs |
|
Operating Voltage |
220-240V Ac, 50 Hz F, single Phase |
The Instrument is supplied with the Following items :
- Main Unit = 1 Nos
- Grease test cups = 6 Nos
- Test tubes = 20 Nos
- Glass Thermometer IP 28C [-6° to +400°C] = 6 Nos
- Rubber Stoppers = 6 Nos
- Test cup Sliding rod = 1 Nos
- Forceps = 2 Nos
- Spatula = 1 Nos
- Test Tube Stand = 1 Nos
Ordering Information :
|
Main Unit |
NI-DP-201 |
|
Grease Test Cups |
NI-DP-01 |
|
Grease Test-tubes |
NI-DP-03 |
|
Glass Thermometer – IP 28C [-6 to +400°C / 2°] |
NI-DP-04 |
|
Rubber Stopper |
NI-DP-05 |
|
Solid State Relay |
NI-DP-06 |
|
Sliding rod |
NI-DP-07 |
|
Stainless Steel forceps |
NI-DP-08 |
|
Stainless Steel Spatula |
NI-DP-09 |
|
Stainless Steel Test-tube Stand |
NI-DP-10 |
|
NABL Calibration test Report |
NI-DP-11 |
Packaging :
The instrument is packed in plywood or any other wooden case with trays. It has heavy support at the base for easy loading & Unloading of the material.
Shipping Details:- (Approx)
- Dimensions :- 36”(L) x 28”(W) x 32”(H) [92cm(L) x 72cm(W) x 82cm(H)]
- Gross Weight = 50-55 Kgs [100-120 Lbs]
Note : Shipping Dimensions & Weight may vary according to the type of packing & wooden box created.
